HomeMy WebLinkAbout20171563.tiffCOLORADO
Department of Public
Health & Environment
Dedicated to protecting and improving the health and environment of the people of Colorado
Weld County - Clerk to the Board
1150O St
PO Box 758
Greeley, CO 80632
May 15, 2017
Dear Sir or Madam:
On May 18, 2017, the Air Pollution Control Division will begin a 30 -day public notice period for JM
Smucker, LLC - Longmont. A copy of this public notice and the public comment packet are enclosed.
Thank you for assisting the Division by posting a copy of this public comment packet in your office.
Public copies of these documents are required by Colorado Air Quality Control Commission
regulations. The packet must be available for public inspection for a period of thirty (30) days from
the beginning of the public notice period. Please send any comment regarding this public notice to
the address below.
Colorado Dept. of Public Health Et Environment
APCD-SS-B1
4300 Cherry Creek Drive South
Denver, Colorado 80246-1530
Attention: Clara Gonzales
Regards,
Clara Gonzales
Public Notice Coordinator
Stationary Sources Program
Air Pollution Control Division
Enclosure
4300 Cherry Creek Drive S., Denver, CO 80246-1530 P 303-692-2000 www.colorado.gov/cdphe
_ John W. Hickenlooper, Governor I Larry Wolk, MD, MSPH, Executive Director and Chief Medical Officer
1 (Jto l tc v ; ems cc : PLC m 1I TP), H LC Pe),
S/31/ I Pc..�.�CeRICHI'"m/CK)
5/3/1-7
2017-1563
Air Pollution Control Division
Notice of a Proposed Project or Activity Warranting Public
Comment
Website Title: JM Smucker, LLC - Longmont - Weld County
Notice Period Begins: May 18, 2017
Notice is hereby given that an application for a proposed project or activity has been submitted to the
Colorado Air Pollution Control Division for the following source of air pollution:
Applicant: JM Smucker, LLC
Facility: Longmont
Uncrustables processing facility
Fairview Street and Peak Avenue, Longmont, County Colorado
Weld County
The proposed project or activity is as follows: The Applicant proposes to construct a new Construction of
new unscrambles processing facility comprising two new identical Haas bread -baking ovens, supported by
two natural gas -fired Hurst boilers, and two silos. An Oxidizer is used to control VOC emission and baghouse
to control Particulate Matter from the silos.
The Division has determined that this permitting action is subject to public comment per Colorado
Regulation No. 3, Part B, Section III.C due to the following reason(s):
• the source is requesting a federally enforceable limit on the potential to emit in order to avoid other
requirements
The Division has made a preliminary determination of approval of the application.
A copy of the application, the Division's analysis, and a draft of Construction Permit 17WE0141 has been
filed with the Weld County Clerk's office. A copy of the draft permit and the Division's analysis are available
on the Division's website at https://www.colorado.gov/pacific/cdphe/air-permit-public-notices
The Division hereby solicits submission of public comment from any interested person concerning the ability
of the proposed project or activity to comply with the applicable standards and regulations of the
Commission. The Division will receive and consider written public comments for thirty calendar days after
the date of this Notice. Any such comment must be submitted in writing to the following addressee:
Sunday A. Fadeyi, P.E.
Colorado Department of Public Health and Environment
4300 Cherry Creek Drive South, APCD-SS-B1
Denver, Colorado 80246-1530
cdphe.commentsapcd@state.co.us
COLORADO
1 I z ;�, fr3
COLORADO
Air Pollution Control Division
Department of Public Health b Environment
CONSTRUCTION PERMIT
Permit number:
DATE ISSUED:
ISSUED TO: JM Smucker, LLC
17WE0141
Facility Name: Longmont
Plant AIRS ID:
Physical Location:
County:
123/9F11
Fairview Street and Peak Avenue, Longmont
Weld
General Description: Uncrustables processing facility
Equipment or activity subject to this permit:
Issuance: 1
Facility
Equipment ID
AIRS
Point
Description
N/A
003
Phase I: One (1) baking oven, model: N/A, SN: N/A, rated at
41,032 pound per hour.
Phase II: One (1) baking oven, model: N/A, SN: N/A, rated at
41,032 pound per hour.
The ovens are equipped with a thermal oxidizer to control VOC emission.
THIS PERMIT IS GRANTED SUBJECT TO ALL RULES AND REGULATIONS OF THE COLORADO AIR QUALITY
CONTROL COMMISSION AND THE COLORADO AIR POLLUTION PREVENTION AND CONTROL ACT C.R.S.
(25-7-101 et seq), TO THOSE GENERAL TERMS AND CONDITIONS INCLUDED IN THIS DOCUMENT AND
THE FOLLOWING SPECIFIC TERMS AND CONDITIONS:
REQUIREMENTS TO SELF -CERTIFY FOR FINAL APPROVAL
1. YOU MUST notify the Air Pollution Control Division (Division) no later than fifteen days after
commencement of operation under this permit by submitting a Notice of Startup (NOS) form to
the Division. The Notice of Startup (NOS) form may be downloaded online at
https://www.colorado.gov/pacific/cdphe/other-air-permitting-notices. Failure to notify the
Division of startup, of the permitted source is a violation of AQCC Regulation Number 3, Part B,
III.G.1 and can result in the revocation of the permit.
2. Within one hundred and eighty days (180) after commencement of operation or issuance of this
permit, whichever is later, compliance with the conditions contained on this permit must be
demonstrated to the Division. It is the permittee's responsibility to self certify compliance with
the conditions. Failure to demonstrate compliance within 180 days may result in revocation of
the permit or enforcement action by the Division. Information on how to certify compliance
was mailed with the permit or can be obtained from the Division's website at
https://www.colorado.gov/pacific/cdphe/air-permit-self-certification. (Reference: Regulation
Number 3, Part B, IlI.G.2).
Page 1 of 7
COLORADO
Air Pollution Control Division
3. The portion of this permit that covers Phase I will expire if the owner or operator of the source
for which this permit was issued: (i) does not commence construction/modification or
operation of this source within 18 months after either, the date of issuance of this construction
permit or the date on which such construction or activity was scheduled to commence as set
forth in the permit application associated with this permit; (ii) discontinues construction for a
period of eighteen months or more; (iii) does not complete construction within a reasonable
time of the estimated completion date. The Division may grant extensions of the deadline per
Regulation Number 3, Part B, III.F.4.b. (Reference: Regulation Number 3, Part B, III.F.4.)
4. The portion of this permit that covers Phase II will expire if the owner or operator of the
source for which this permit was issued: (i) does not commence construction/modification or
operation of the second baking oven within 18 months after June 1, 2022; (ii) discontinues
construction of the second baking oven for a period of eighteen months or more; (iii) does not
complete construction within a reasonable time of the estimated completion date of the
second baking oven. The Division may grant extensions of the deadline per Regulation Number
3, Part B, III.F.4.b. (Reference: Regulation Number 3, Part B, III.F.4.)
5. Within one hundred and eighty days (180) after commencement of operation or issuance of this
permit, whichever is later, the operator must complete all initial compliance testing and
sampling as required in this permit and submit the results to the Division as part of the self -
certification process. (Reference: Regulation Number 3, Part B, III.G.2.)
6. Within thirty (30) days after commencement of operation or issuance of this permit, whichever
is later, the permit number must be marked on the subject equipment for ease of
identification. (Reference: Regulation Number 3, Part B, III.E.) (State only enforceable)
7. The owner or operator must develop an operating and maintenance (OEM) plan, along with a
recordkeeping format, that outlines how the applicant will maintain compliance on an ongoing
basis with the requirements of this permit. Compliance with the O&M plan must commence
at startup. Within one hundred and eighty days (180) after commencement of operation or
issuance of this permit, whichever is later, the owner or operator must submit the OEM plan to
the Division. Failure to submit an acceptable operating and maintenance plan could result in
revocation of the permit. Note that the Division may modify the monitoring requirements as
part of the Title V Operating Permit if this facility is subject to Title V permitting (Reference:
Regulation Number 3, Part B, III.G.2.).
8. Within thirty (30) days after commencement of operation or issuance of this permit, whichever
is later, the permit number must be marked on the subject equipment for ease of
identification. (Reference: Regulation Number 3, Part B, III.E.) (State only enforceable)
9. The manufacturer, model number of the subject equipment must be provided to the Division
within one hundred and eighty days (180) after commencement of operation or issuance of this
permit, whichever is later. (Reference: Regulation Number 3, Part B, III.G.2.)
EMISSION LIMITATIONS AND RECORDS
10. Emissions of air pollutants must not exceed the following limitations. Monthly records of the
actual emission rates must be maintained by the applicant and made available to the Division
for inspection upon request. (Reference: Regulation Number 3, Part B, II.A.4.)
Monthly Limits:
Facility
Equipment ID
AIRS
Point
Tons per Month
Emission
Type
PM
PM,o
PM2,5
5O2
NO),
VOC
CO
N/A
001
--
--
--
--
0.5
0.5
0.4
Point
Note: Monthly limits are based on a 31 -day month.
The owner or operator must calculate monthly emissions based on the calendar month.
Page 2 of 7
COLORADO
Air Pollution Control Division
t oar:z ent
Annual Limits:
Facility
Equipment ID
AIRS
Point
Tons per Year
Emission
Type
PM
PM10
FM2.5
SO2
NO.
VOC
CO
N/A
003
--
--
--
--
5.9
6.1
5.0
Point
ee "Notes to Permit Holder" for information on emission factors and methods used to calculate
limits.
During the first twelve (12) months of operation, compliance with both the monthly and annual
emission limitations is required. After the first twelve (12) months of operation, compliance with
only the annual limitation is required.
Compliance with the annual limits, for the criteria pollutants, must be determined on a rolling
twelve (12) month total. By the end of each month, a new twelve-month total is calculated
based on the previous twelve months' data. The permit holder must calculate actual emissions
each month and keep a compliance record on site or at a local field office with site
responsibility for Division review.
All emission calculations must be made using the emission factors and format specified in Notes
to Permit Holder. The owner or operator must petition the Division, and receive Division
approval in writing, prior to the use of any other method of calculating emissions.
11. The following control equipment shall be maintained and operated to ensure satisfactory
performance. The uncontrolled emissions shall be reduced by at least the control
efficiencies listed below. The owner or operator shall monitor compliance with this condition
through the results of approved compliance tests (when required), compliance with the
Operating and Maintenance Plan, compliance records, and other methods as approved by the
Division. (Reference: Regulation No. 3, Part B, Section III.E.)
Facility
Equipment ID
AIRS
Point
Control Device
Controlled Pollutants
Control Efficiency
N/A
003
Oxidizer
VOC
98.0 %
PROCESS LIMITATIONS AND RECORDS
12. This source must be limited to the following maximum consumption, processing and/or
operational rates as listed below. Monthly records of the actual process rate must be
maintained by the applicant and made available to the Division for inspection upon request.
(Reference: Regulation Number 3, Part B, II.A.4)
Process/Consumption Limits:
Facility
Equipment ID
AIRS
Point
Process Parameter
Annual and Monthly Limits
N/A
003
Bread production
Shall be limited by the VOC limit above
Natural gas consumption
118.5 MMscf/year and 10.1 MMscf/month
The monthly limits included in this permit were derived from the annual limits based on a 31 -
day month. The owner or operator must calculate monthly process rates based on the calendar
month.
During the first twelve (12) months of operation, compliance with both the monthly and yearly
process limitations must be required. After the first twelve (12) months of operation, compliance
with only the yearly limitation must be required.
Compliance with the yearly process limits must be determined on a rolling twelve (12) month
total. By the end of each month, a new twelve-month total is calculated based on the previous
twelve months' data. The permit holder must calculate monthly process rates and keep a
compliance record on site or at a local field office with site responsibility, for Division review.
Page 3 of 7
COLORADO
Air Pollution Control Division
STATE AND FEDERAL REGULATORY REQUIREMENTS
13. Visible emissions must not exceed twenty percent (20%) opacity during normal operation of the
source. During periods of startup, process modification, or adjustment of control equipment
visible emissions must not exceed 30% opacity for more than six minutes in any sixty
consecutive minutes. Opacity must be determined using EPA Method 9. (Reference: Regulation
Number 1, II.A.1. a 4.)
14. This source is subject to the odor requirements of Regulation Number 2. (State only
enforceable)
15. This source is located in an ozone non -attainment or attainment -maintenance area and subject
to the Reasonably Available Control Technology (RACT) requirements of Regulation Number 3,
Part B, III.D.2. RACT for this source has been determined to be the application of Oxidizer for
the control of VOC.
OPERATING Ft MAINTENANCE REQUIREMENTS
16. The owner or operator must develop an operating and maintenance (O&M) plan, along with a
recordkeeping format, that outlines how the applicant will maintain compliance on an ongoing
basis with the requirements of this permit. Compliance with the OftM plan must commence at
startup. Within one hundred and eighty days (180) after commencement of operation or
issuance of this permit, whichever is later, the owner or operator must submit the OO.M plan to
the Division. Failure to submit an acceptable operating and maintenance plan could result in
revocation of the permit. Note that the Division may modify the monitoring requirements as
part of the Title V Operating Permit if this facility is subject to Title V permitting (Reference:
Regulation Number 3, Part B, III.G.2.).
COMPLIANCE TESTING AND SAMPLING
Initial Testing Requirements
17. Initial testing is not required for this source.
Periodic Testing Requirements
18. Periodic testing is not required for this source.
ADDITIONAL REQUIREMENTS
19. The permit number shall be marked on the subject equipment for ease of identification.
(Reference: Regulation Number 3, Part B, III.E.) (State only enforceable)
20. A Revised Air Pollutant Emission Notice (APEN) must be filed: (Reference: Regulation Number
3, Part A, II.C.)
a. By April 30 of the year following a significant increase in emissions. A significant
increase in emissions is defined as follows:
For any criteria pollutant:
For sources emitting less than 10O tons per year, a change in actual emissions of five
tons per year or more, above the level reported on the last APEN submitted; or
For volatile organic compounds (VOC) and nitrogen oxide (NOx) sources in an ozone
non -attainment area emitting less than 100 tons of VOC or nitrogen oxide per year, a
change in actual emissions of one ton per year or more or five percent, whichever is
greater, above the level reported on the last APEN submitted; or
Page 4 of 7
COLORADO
Air Pollution Control Division
i:,part:rk:r:t i%ubt'':I, lieuh. c G!::iror;rne�;t
For sources emitting 100 tons per year or more of a criteria pollutant, a change in
actual emissions of five percent or 50 tons per year or more, whichever is less, above
the level reported on the last APEN submitted; or
For sources emitting any amount of lead, a change in actual emissions, above the level
reported on the last APEN submitted, of fifty (50) pounds of lead
For any non -criteria reportable pollutant:
If the emissions increase by 50% or five (5) tons per year, whichever is less, above the
level reported on the last APEN submitted to the Division.
b. Whenever there is a change in the owner or operator of any facility, process, or
activity; or
c. Whenever new control equipment is installed, or whenever a different type of control
equipment replaces an existing type of control equipment; or
d. Whenever a permit limitation must be modified; or
e. No later than 30 days before the existing APEN expires.
21. The requirements of Colorado Regulation Number 3, Part D apply at such time that any
stationary source or modification becomes a major stationary source or major modification
solely by virtue of a relaxation in any enforceable limitation that was established after August
7, 1980, on the capacity of the source or modification to otherwise emit a pollutant such as a
restriction on hours of operation (Colorado Regulation Number 3, Part D, V.A.7.B).
With respect to this Condition, Part D requirements may apply to future modifications if
emission limits are modified to equal or exceed the following threshold levels:
Facility
Equipment ID
AIRS
Point
Equipment
Description
Pollutant
Emissions - tons per year
Threshold
Current permit limit
N/A
003
Backing ovens
VOC
100
6.1
GENERAL TERMS AND CONDITIONS:
22. This permit and any attachments must be retained and made available for inspection upon
request. The permit may be reissued to a new owner by the Division as provided in Regulation
Number 3, Part B, II.B upon a request for transfer of ownership and the submittal of a revised
APEN, and the required fee.
23. If this permit specifically states that final approval has been granted, then the remainder of
this condition is not applicable. Otherwise, the issuance of this construction permit is
considered initial approval and does not provide "final" approval for this activity or operation of
this source. Final approval of the permit must be secured from the APCD in writing in
accordance with the provisions of 25-7-114.5(12)(a) C.R.S. and AQCC Regulation Number 3,
Part B, III.G. Final approval cannot be granted until the operation or activity commences and
has been verified by the APCD as conforming in all respects with the conditions of the permit.
Once self -certification of all points has been reviewed and approved by the Division, it will
provide written documentation of such final approval. Details for obtaining final approval to
operate are located in the Requirements to Self -Certify for Final Approval section of this
permit. The operator must retain the permit final approval letter issued by the Division after
completion of self -certification with the most current construction permit.
24. This permit is issued in reliance upon the accuracy and completeness of information supplied
by the applicant and is conditioned upon conduct of the activity, or construction, installation
and operation of the source, in accordance with this information and with representations
made by the applicant or applicant's agents. It is valid only for the equipment and operations
Page 5 of 7
COLORADO
Air Pollution Control Division
or activity(ies) specifically identified in this permit. If subsequent operations or testing at the
source indicate the information supplied to obtain this permit and relied upon in the creation
and issuance of this permit is inaccurate, the source must submit an application to modify the
permit to address the inaccuracy(ies). (Reference: Regulation Number 3, Part B III.E.)
By: By:
Sunday Fadeyi, P.E.
Permit Engineer
Permit History
R K Hancock III, P.E.
Construction Permits Unit Supervisor
Issuance
Date
Description
Issuance 1
This issuance
Initial issued to JM Smucker, LLC
Notes to Permit Holder (as of date of permit issuance):
1) The production or raw material processing limits and emission limits contained in this permit
are based on the production/processing rates requested in the permit application. These limits
may be revised upon request of the permittee providing there is no exceedence of any specific
emission control regulation or any ambient air quality standard. A revised air pollutant emission
notice (APEN) and application form must be submitted with a request for a permit revision.
(Reference: Regulation Number 3, Part B II.A.4.)
2) This source is subject to the Common Provisions Regulation Part II, Subpart E, Affirmative
Defense Provision for Excess Emissions During Malfunctions. The permittee must notify the
Division of any malfunction condition which causes a violation of any emission limit or limits
stated in this permit as soon as possible, but no later than noon of the next working day,
followed by written notice to the Division addressing all of the criteria set forth in Part II.E.1.
of the Common Provisions Regulation. See: https://www.colorado.gov/pacific/cdphe/aqcc-
regs.
3) The emission levels contained in this permit are based on the following emission factors:
Point 003 - Bread production:
Volatile Organic Compounds (VOC):
Shall be determined by applying the following
equation culled from Air Emissions Inventory
Improvement Program (EIIP) Vol. II, Chapter 14, page
14A - 83:
VOCEF = (0.95Y1 + 0.195Ti - 0.51S - 0.86Ts + 1.90) lbs per ton of baked product produced,
Where: Yi = Initial Baker's % of yeast,
Ti = Total Yeast Action Time (hours),
S = Spike (Final Baker's Percent of Yeast) and
Ts = Spiking Time (hours).
VOC Emission (tons/year) = Production Rate (ton/year)*VOCEF (lbs/ton)*(tons/2000 lbs)
Point 003 - Natural Gas Combustion:
CAS
Pollutant
Emission Factors Applied lbs per MMscf consummed
Source
Uncontrolled
Controlled
NOX
100.000
100.000
AP -42
VOC
5.500
5.500
AP -42
CO
84.000
84.000
AP -42
Page 6 of 7
COLORADO
Air Pollution Control Division
IDeparrnerd'':.t VliLi ", r E•, t - `L!;C
4) In accordance with C.R.S. 25-7-114.1, each Air Pollutant Emission Notice (APEN) associated
with this permit is valid for a term of five years from the date it was received by the Division. A
revised APEN shall be submitted no later than 30 days before the five-year term expires. Please
refer to the most recent annual fee invoice to determine the APEN expiration date for each
emissions point associated with this permit. For any questions regarding a specific expiration
date call the Division at (303)-692-3150.
5) This facility is classified as follows:
Applicable
Requirement
Status
Operating Permit
Synthetic minor: VOC; Minor: PM, NOx, CO
NANSR
Synthetic minor: VOC; Minor: PM, NOx, CO
6) The permit holder is required to pay fees for the processing time for this permit. An invoice for
these fees will be issued after the permit is issued. Failure to pay the invoice will result in
revocation of this permit. The permit holder must pay the invoice within 30 days of receipt of
the invoice (Reference: Regulation Number 3, Part A, VI.B.).
7) Unless specifically stated otherwise, the general and specific conditions contained in this
permit have been determined by the Division to be necessary to assure compliance with the
provisions of Section 25-7-114.5(7)(a), C.R.S.
8) Each and every condition of this permit is a material part hereof and is not severable. Any
challenge to or appeal of a condition hereof must constitute a rejection of the entire permit
and upon such occurrence, this permit must be deemed denied ab initio. This permit may be
revoked at any time prior to self -certification and final authorization by the Division on grounds
set forth in the Colorado Air Pollution Prevention and Control Act and regulations of the AQCC
including failure to meet any express term or condition of the permit. If the Division denies a
permit, conditions imposed upon a permit are contested by the applicant, or the Division
revokes a permit, the applicant or owner or operator of a source may request a hearing before
the AQCC for review of the Division's action. (Reference: Regulation Number 3, Part B III.F.)
9) Section 25-7-114.7(2)(a), C.R.S. requires that all sources required to file an Air Pollutant
Emission Notice (APEN) must pay an annual emission fee. If a source or activity is to be
discontinued, the owner must notify the Division in writing requesting a cancellation of the
permit. Upon notification, annual fee billing will terminate.
10) Violation of the terms of a permit or of the provisions of the Colorado Air Pollution Prevention
and, Control Act or the regulations of the AQCC may result in administrative, civil or criminal
enforcement actions under Sections 25-7-115 (enforcement), -121 (injunctions), -122 (civil
penalties), -122.1 (criminal penalties), C.R.S.
Page 7 of 7
COLORADO
Air Pollution Control Division
AIR POLLUTION CONTROL DIVISION
PRELIMINARY ANALYSIS
DATE:
May 12, 2017
PERMIT NUMBER: 17WE0141, 17WE0140, 17WE0139
APPLICANT: JM Smucker, LLC.
REVIEW ENGINEER: Sunday Fadeyi, P.E.
CONTROL ENGINEER: R K Hancock III, P.E
PROJECT DESCRIPTION
JM Smucker, LLC. — Uncrustables processing facility - Weld County
The Applicant proposes to limit VOC emissions and obtain a synthetic minor permit for their new Uncrustables
bakery and processing facility located in Weld County, Colorado.
The source's emissions profile is as follows:
SUMMARY OF FACILITY WIDE EMISSIONS
EMISSIONS (tons/year)
TSP
PMto
PM2.5
SO2
NOx
VOC
CO
HAPe
REMARKS
Current Project Emission
1.6
1.5
1.2
0.1
11.7
6.7
14.6
Synthetic Minor
Construction
Potential To Emit
65.3
42.5
36.9
0.1
17.4
288.2
14.6
Permit & PSD
SOURCE'S IMPACTS (µe/r„3_)
For the Criteria Air Pollutant emissions, the source's impact analysis is not required at this time per the Colorado
Modeling Guideline for Air Quality Permits, Table 1. Therefore, it is assumed that the source, as proposed, will not
cause any violation of the National Ambient Air Quality Standards.
SOURCE CLASSIFICATION
The project has the potential to emit (PTE) of VOC at 288.2 tons per year which is above the major source level but
the actual VOC emission being less the 100 tons per year. Hence, the facility is a synthetic minor source for VOC.
Therefore, the source's request to limit VOC PTE emission below the major source treshold triggers public notice
requirement.
Page 1 of 1
General APEN - Form APCD-200
Air Pollutant Emission Notice (APEN) and
Application for Construction Permit
All sections of this APEN and application must be completed for both new and existing facilities, including APEN
updates. An application with missing information may be determined incomplete and may be returned or result in
longer application processing times. You may be charged an additional APEN fee if the APEN is filled out
incorrectly or is missing information and requires re -submittal.
There may be a more specific APEN for your source (e.g. paint booths, mining operations, engines, etc.). A list of
specialty APENs is available on the Air Pollution Control Division (APCD) website at
www.colorado.gov/pacific/cdphe/air-permits.
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation No. 3, Part A, II.C. for revised APEN requirements.
Permit Number:
ilwEar7?ci
AIRS ID Number: 'ZS /gFiI / 0O
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 1 - Administrative Information
Company Name1: JM Smucker, LLC
Site Name: Longmont
Site Location: Fairview Street and Peak Avenue
Longmont, CO 80504
Mailing Address:
(Include Zip Code) One Strawberry Lane
Portable Source
Home Base:
Orrville, OH 44667
Site Location
County: Weld
NAICS or SIC Code: 2038
Permit Contact: Brian Kinsey
Phone Number: _ G y _ 3 C6 7
E -Mail Address2: brian.kinsey@jmsmucker.com
1 Please use the full, legal company name registered with the Colorado Secretary of State. This is the company name that will
appear on all documents issued by the APCD. Any changes will require additional paperwork.
2Permits, exmption letters, and any processing invoices will be issued by APCD via e-mail to the address provided.
358308
COLORADO
Form APCD-200 - General APEN - Revision 7/2015
Permit Number: AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 2- Requested Action
2 NEW permit OR newly -reported emission source (check one below)
2 STATIONARY source ❑ PORTABLE source
-OR -
❑ MODIFICATION to existing permit (check each box below that applies)
❑ Change fuel or equipment ❑ Change company name ❑ Add point to existing permit
❑ Change permit limit ❑ Transfer of ownership' ❑ Other (describe below)
OR-
❑ APEN submittal for update only (Please note blank APENs will not be accepted)
- ADDITIONAL PERMIT ACTIONS -
❑ Limit Hazardous Air Pollutants (HAPs) with a federally -enforceable limit on Potential To Emit (PTE)
❑ APEN submittal for permit exempt/grandfathered source
Additional Info Ft Notes:
see project narrative
3 For transfer of ownership, a completed Transfer of Ownership Certification Form (Form APCD-104) must be submitted.
Section 3 - General Information
General description of equipment and purpose:
Boilers
Manufacturer: TBD Model No.: TBD Serial No.: TBD
Company equipment Identification No. (optional):
For existing sources, operation began on:
For new, modified, or reconstructed sources the projected start-up date is: 9/2018
2 Check this box if operating hours are 8,760 hours per year; if fewer, fill out the fields below:
Normal Hours of Source Operation: hours/day
Seasonal use percentage: Dec -Feb: Mar -May:
days/week weeks/year
June -Aug: Sept -Nov:
Form APCD-200 - General APEN - Revision 7/2015 2 I A.V
COLORADO
D. C.6 Env. .4
Permit Number:
AIRS ID Number:
/ /
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 4 - Processing/Manufacturing Information Ft Material Use
Check box if this information is not applicable to source or process
From what year is the actual annual amount?
Description
Design Process
Rate
(Specify Units)
Actual Annual
Amount
(Specify Units)
Requested Annual
Permit Limit"
(Specify Units)
Material
Consumption:
Finished
Product(s):
Requested values will become permit limitations. Requested limit(s) should consider future process growth.
Section 5 - Stack Information
Geographical Coordinates
(Latitude/Longitude or UTM)
40.1666555, -105.038308
❑ Check box if the following information is not applicable to the source because emissions will not be emitted from a
stack. If this is the case, the rest of this section may remain blank.
Operator
Stack iD No.
N- '.
Discharge .Height
�•
Above Ground Level
(Feet)
Temp;
. F -
( ).
Flow Rate
4CFM
( ),
Velocity
ft/sec
(f )
45.58
140
17042
0.66
Indicate the direction of the stack outlet: (check one)
❑r Upward
❑ Horizontal
❑ Downward
❑ Other (describe):
Indicate the stack opening and size: (check one)
❑ Upward with obstructing raincap
❑✓ Circular Interior stack diameter (inches): 24
❑ Square/rectangle Interior stack width (inches): Interior stack depth (inches):
❑ Other (describe):
Form APCD-200 - General APEN - Revision 7/2015 3
A®
COLORADO
Iliarablic
Ku. 6 Emtrarunrm
Permit Number:
AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 6 - Combustion Equipment Et Fuel Consumption Information
❑ Check box if this information is not applicable to the source (e.g. there is no fuel -burning equipment associated
with this emission source)
Design Input Rate ,
(MMBTU/hr)
Actual Annual Fuel Use
(Specify Units)
Requested Annual Permit Limit4
(Specify Units)
26.78
_26: -78 ----
From what year is the actual annual fuel use data?
Indicate the type of fuel used5:
❑■ Pipeline Natural Gas (assumed fuel heating value of 1,020 BTUISCF)
❑ Field Natural Gas Heating value: BTU/SCF
❑ Ultra Low Sulfur Diesel (assumed fuel heating value of 138,000 BTU/gallon)
❑ Propane (assumed fuel heating value of 2,300 BTU/SCF)
❑ Coal Heating value: BTU/lb Ash Content: Sulfur Content:
❑ Other (describe): Heating value (give units):
a Requested values will become permit limitations. Requested limit(s) should consider future process growth.
5 If fuel heating value is different than the listed assumed value, please provide this information in the "Other" field.
Section 7 - Criteria Pollutant Emissions Information
Attach all emission calculations and emission factor documentation to this APEN form.
Is any emission control equipment or practice used to reduce emissions? ® Yes ❑ No
- If yes, please describe the control equipment AND state the overall control efficiency (% reduction):
Pollutant
Control Equipment Description
Overall Control Efficiency
(% reduction in emissions)
TSP (PM)
PM10
PM25
SOX
NOx
low NOx burners
TBD
CO
VOC
Other:
Form APCD-200 - General APEN - Revision 7/2015
41
A®
Deparoraem al Pub.
COLORADO
",
Permit Number:
AIRS ID Number:
Section 7 (continued)
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
From what year is the following reported actual annual emissions data?
Use the following table to report the criteria pollutant emissions from source:
(Use the data reported in Sections 4 and 6 to calculate these emissions.)
Uncontrolled
Emission
Factor
(Specify Units)
Emission
-
Factor
Source
(AP -41, Mfg•
etc)
Actual Annual Emissions
,
Requested Annual Permit
4 a
Emission Limit(s)4
Uncontrolled
(Tons/year)
Controlled6
(Tons/year)
Uncontrolled
(Tons/year)
Controlled
(Tons/year)
TSP (PM)
7.6
AP -42
.87
.87
PM1a
PM2.5
SO,,
.6
AP -42
.07
.07
NO.
100
AP -42
11.5
11.5
CO
84
AP -42
9.66
9.66
VOC
5.5
AP -42
.63
.63
Other:
4Requested values will become permit limitations. Requested limit(s) should consider future process growth.
6Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
Section 8 - Non -Criteria Pollutant Emissions Information
Does the emissions source have any uncontrolled actual emissions of non -criteria
pollutants (e.g. HAP- hazardous air pollutant) equal to or greater than 250 lbs/year? 0Yes No
If yes, use the following table to report the non -criteria pollutant (HAP) emissions from source:
CAS
Number
Chemical Name
Overall
Control
Efficiency
Uncontrolled
Emission
Factor
(specify units)
Emission Factor
Source
(AP -41, Mfg. etc)
Uncontrolled
Actual
Emissions '
Ohs/year)
Controlled
Actual
Emissions e
(lbs/year)
6Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
Form APCD-200 - General APEN - Revision 7/2015
COLORADO
5 I ®, a..�,..,,,.,.�
XM��T6 fJ�HIonT��+
Permit Number: AIRS ID Number: / /
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 9 - Applicant Certification
I hereby certify that all information contained herein and information submitted with this application is complete, true
and correct.
2//17
Signature of Legally Authorized Person (not a vendor or consultant) Date
(-JA7�i (i.1‘ �1inlJZN
(Ace_ 1 426..t V7efc �cas
Name (please print) Title
Check the appropriate box to request a copy of the:
❑ Engineer's Preliminary Analysis conducted
j Draft permit prior to issuance
E Draft permit prior to public notice
(Checking any of these boxes may result in an increased fee and/or processing time)
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation No. 3, Part A, II.C. for revised APEN requirements.
Send this form along with $152.90 to:
Colorado Department of Public Health and
Environment
Air Pollution Control Division
APCD-SS-B1
4300 Cherry Creek Drive South
Denver, CO 80246-1530
Telephone: (303) 692-3150
Form APCD-200 - General APEN - Revision 7/2015
For more information or assistance call:
Small Business Assistance Program
(303) 692-3175 or (303) 692-3148
Or visit the APCD website at:
www.colorado.gov/pacific/cdphe/air-permits
®® COLORADO
General APEN - Form APCD-200
Air Pollutant Emission Notice (APEN) and
Application for Construction Permit
All sections of this APEN and application must be completed for both new and existing facilities, including APEN
updates. An application with missing information may be determined incomplete and may be returned or result in
longer application processing times. You may be charged an additional APEN fee if the APEN is filled out
incorrectly or is missing information and requires re -submittal.
There may be a more specific APEN for your source (e.g. paint booths, mining operations, engines, etc.). A list of
specialty APENs is available on the Air Pollution Control Division (APCD) website at
www.colorado.gov/pacific/cdphe/air-permits.
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation No. 3, Part A, II.C. for revised APEN requirements.
Permit Number:
1'7wEO/Lo
AIRS ID Number: j23 /9Fi1 /DC2,
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 1 - Administrative Information
Company Name1: JM Smucker, LLC
Site Name: Longmont
Site Location: Fairview Street and Peak Avenue
Longmont, CO 80504
Mailing Address:
(Include Zip Code) One Strawberry Lane
Portable Source
Home Base:
Orrville, OH 44667
Site Location
County: Weld
NAICS or SIC Code: 2038
Permit Contact: Brian Kinsey
Phone Number: 3 30 G 8y —? 6( 7
E -Mail Address2: brian.kinsey@jmsmucker.com
1 Please use the full, legal company name registered with the Colorado Secretary of State. This is the company name that will
appear on alt documents issued by the APCD. Any changes will require additional paperwork.
2Permits, exmption letters, and any processing invoices will be issued by APCD via e-mail to the address provided.
Form APCD-200 - General APEN - Revision 7/2015
358309
®®COLORADO
nW .....
Permit Number: AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 2- Requested Action
El NEW permit OR newly -reported emission source (check one below)
❑✓ STATIONARY source ❑ PORTABLE source
-OR -
D MODIFICATION to existing permit (check each box below that applies)
❑ Change fuel or equipment ❑ Change company name LI Add point to existing permit
❑ Change permit limit ❑ Transfer of ownership3 ❑ Other (describe below)
OR -
APEN submittal for update only (Please note blank APENs wilt not be accepted)
- ADDITIONAL PERMIT ACTIONS -
Limit Hazardous Air Pollutants (HAPs) with a federally -enforceable limit on Potential To Emit (PTE)
❑ APEN submittal for permit exempt/grandfathered source
Additional Info Et Notes:
see project narrative
3 For transfer of ownership, a completed Transfer of Ownership Certification Form (Form APCD-104) must be submitted.
Section 3 - General Information
General description of equipment and purpose:
Flour Silos
Manufacturer: TBD Model No.: TBD Serial No.: TBD
Company equipment Identification No. (optional):
For existing sources, operation began on:
For new, modified, or reconstructed sources the projected start-up date is: 9/2018
El Check this box if operating hours are 8,760 hours per year; if fewer, fill out the fields below:
Normal Hours of Source Operation: hours/day
Seasonal use percentage: Dec -Feb: Mar -May:
days/week weeks/year
June -Aug: Sept -Nov:
Form APCD-200 - General APEN - Revision 7/2015 2 I
Efr
COLORADO
o.a.mm.ea Public
Permit Number:
AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 4 - Processing/Manufacturing Information a Material Use
❑ Check box if this information is not applicable to source or process
From what year is the actual annual amount?
Description
Design Process
Rate
(Specify Units)
Actual Annual
Amount
(Specify Units)
Requested Annual
Permit Limit4
(Specify Units) "?
Material
.:. Consumption:.
White wheat flour
40,000 lbs/hr
40,000 lbs/hr
40,000 lbs/hr
Whole wheat flour
40,000 lbs/hr
40,000 lbs/hr
40,000 lbs/hr
Finished
Product(s):
4
Requested values will become permit limitations. Requested limit(s) should consider future process growth.
Section 5 - Stack Information
Geographical Coordinates
(Latitude/Longitude or UTM)
❑� Check box if the following information is not applicable to the source because emissions will not be emitted from a
stack. If this is the case, the rest of this section may remain blank.
Operator =�
Stack ID No
Discharge Hei ht
Above Grou �cl Level fi
Feet
Tem
p',
( F)
Flow Rate
(stCFM)'
Velocity
(fttsec)
Indicate the direction of the stack outlet: (check one)
❑ Upward
❑ Horizontal
❑ Downward
❑ Other (describe):
❑ Upward with obstructing raincap
Indicate the stack opening and size: (check one)
❑ Circular Interior stack diameter (inches):
❑ Square/rectangle Interior stack width (inches): Interior stack depth (inches):
❑ Other (describe):
Form APCD-200 - General APEN - Revision 7/2015 3 I
COLORADO
Department. Putter
H*ath6 t. ,,unm
Permit Number:
AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 6 - Combustion Equipment £t Fuel Consumption Information
E Check box if this information is not applicable to the source (e.g. there is no fuel -burning equipment associated
with this emission source)
Design Input Rate
(MMBTU/hr)
Actual Annual Fuel Use
(Specify Units)
Requested Annual Permit Limit4
(Specify Units)
From what year is the actual annual fuel use data?
Indicate the type of fuel useds:
❑ Pipeline Natural Gas (assumed fuel heating value of 1,020 BTU/SCF)
O Field Natural Gas Heating value: BTU/SCF
❑ Ultra Low Sulfur Diesel (assumed fuel heating value of 138,000 BTU/gallon)
❑ Propane (assumed fuel heating value of 2,300 BTU/SCF)
❑ Coal Heating value: BTU/lb Ash Content: Sulfur Content:
❑ Other (describe): Heating value (give units):
a Requested values will become permit limitations. Requested limit(s) should consider future process growth.
5 If fuel heating value is different than the listed assumed value, please provide this information in the "Other" field.
Section 7 - Criteria Pollutant Emissions Information
Attach all emission calculations and emission factor documentation to this APEN form.
Is any emission control equipment or practice used to reduce emissions? ❑ Yes ® No
If yes, please describe the control equipment AND state the overall control efficiency (% reduction):
Pollutant
Control Equipment Description
Overall Control Efficiency
(% reduction in emissions)
TSP (PM)
Dust collection - polyester felt filter
TBD - est. 99.5% at 3 micron
PM,.
Dust collection - polyester felt filter
TBD - est. 99.5% at 3 micron
PM2.s
Dust collection - polyester felt filter
TBD - est. 99.5% at 3 micron
SOX
NOX
CO
VOC
Other:
Form APCD-2OO - General APEN - Revision 7/2015
4I
Deparlment
COLORADO
d
HerOcha Snwumm
Permit Number:
AIRS ID Number:
/ /
Section 7 (continued)
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
From what year is the following reported actual annual emissions data?
Use the following table to report the criteria pollutant emissions from source:
(Use the data reported in Sections 4 and 6 to calculate these emissions.)
Pollutant
Uncontrolled
Emission
Factor
(Specify Units)
Emission
Factor
Source
(AP -42 Mfg.
et)
Actual Annual Emissions
Requested Anntta:i Permit
.� Emt�h
iss�omitts�#
Uncontrolled
(Tons/year)
Controlled'
(Tons/year)
Uncontrolled
(Tons/year)
Controlled
(Tons/year)
TSP (PM)
0.18
AP -42
31.54
31.54
PM10
0.059
AP -42
10.34
10.34
PMZ5
0.01
AP -42
1.75
1.75
Sox
NO,,
CO
VOC
Other:
4Requested values will become permit limitations. Requested limit(s) should consider future process growth.
'Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
section 8 - Non -Criteria Pollutant Emissions Information
Does the emissions source have any uncontrolled actual emissions of non -criteria
pollutants (e.g. HAP- hazardous air pollutant) equal to or greater than 250 lbs/year? 0Yes
If yes, use the following table to report the non -criteria pollutant (HAP) emissions from source:
CAS
Number
Chemical Name
Overall
Control
Efficiency
Uncontrolled
Emission
Factor
(specify units)
Emission Factor
Source
(AP -42, Mfg. etc)
Uncontrolled
Actual
Emissions
(lbs/year)
Controlled
Actual
Emissions s
(lbs/year)
No
'Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
Form APCD-200 - General APEN - Revision 7/2015
COLORADO
5 I
iWMb 4MNn.Mn
Permit Number: AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 9 - Applicant Certification
I hereby certify that all information contained herein and information submitted with this application is complete, true
and correct.
Signature
Signature of Legally Authorized Person (not a vendor or consultant) Date
6e ! rtS,Cfe� (e-rG i�c.tS
Name (please print) Title
Check the appropriate box to request a copy of the:
El Engineer's Preliminary Analysis conducted
❑r Draft permit prior to issuance
❑� Draft permit prior to public notice
(Checking any of these boxes may result in an increased fee and/or processing time)
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation No. 3, Part A, II.C. for revised APEN requirements.
Send this form along with $152.90 to:
Colorado Department of Public Health and
Environment
Air Pollution Control Division
APCD-SS-B 1
4300 Cherry Creek MN - South
Denver, CO 80246-1530
Telephone: (303) 692-3150
For more information or assistance call:
Small Business Assistance Program
(303) 692-3175 or (303) 692-3148
Or visit the APCD website at:
www.colorado.gov/pacific/cdphe/air-permits
Form APCD-200 - General APEN - Revision 7/2015 6
A®
COLORADO
Department or Public
WO. b Emlrv.uwsu
General APEN - Form APCD-200
Air Pollutant Emission Notice (APEN) and
Application for Construction Permit
All sections of this APEN and application must be completed for both new and existing facilities, including APEN
updates. An application with missing information may be determined incomplete and may be returned or result in
longer application processing times. You may be charged an additional APEN fee if the APEN is filled out
incorrectly or is missing information and requires re -submittal.
There may be a more specific APEN for your source (e.g. paint booths, mining operations, engines, etc.). A list of
specialty APENs is available on the Air Pollution Control Division (APCD) website at
www.colorado.gov/pacific/cdphe/air-permits.
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation No. 3, Part A, II.C. for revised APEN requirements.
Permit Number:
17WE 014-1
AIRS ID Number: /23 III 003
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 1 - Administrative Information
Company Name:
Site Name:
JM Smucker, LLC
Longmont
Site Location: Fairview Street and Peak Avenue
Longmont, CO 80504
Mailing Address:
(Include Zip Code) One Strawberry Lane
Portable Source
Home Base:
Orrville, OH 44667
Site Location
County: Weld
NAICS or SIC Code: 2038
Permit Contact: Brian Kinsey
Phone Number: —7 30 C (5,y_ 76 6 ?
E -Mail AddressZ• brian.kinsey@jmsmucker.com
1 Please use the full, legal company name registered with the Colorado Secretary of State. This is the company name that will
appear on all documents issued by the APCD. Any changes will require additional paperwork.
2Permits, exmption letters, and any processing invoices will be issued by APCD via e-mail to the address provided.
Form APCD-200 - General APEN - Revision 7/2015
358310
COLORADO
1 I A ap,.m��dewb�
XrIC� b Un�ronmm�
Permit Number: AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 2- Requested Action
2 NEW permit OR newly -reported emission source (check one below)
2 STATIONARY source ❑ PORTABLE source
-OR-
❑ MODIFICATION to existing permit (check each box below that applies)
❑ Change fuel or equipment ❑ Change company name El Add point to existing permit
❑ Change permit limit ❑ Transfer of ownership3 ❑ Other (describe below)
-OR -
❑ APEN submittal for update only (Please note blank APENs will not be accepted)
- ADDITIONAL PERMIT ACTIONS -
El Limit Hazardous Air Pollutants (HAPs) with a federally -enforceable limit on Potential To Emit (PTE)
❑ APEN submittal for permit exempt/grandfathered source
Additional Info £t Notes:
see project narrative
3 For transfer of ownership, a completed Transfer of Ownership Certification Form (Form APCD-104) must be submitted.
Section 3 - General Information
General description of equipment and purpose: Bread process line - emissions from two identical ovens
Manufacturer: TBD Model No.: TBD Serial No.: TBD
Company equipment Identification No. (optional):
For existing sources, operation began on:
For new, modified, or reconstructed sources the projected start-up date is: 9/2018
0 Check this box if operating hours are 8,760 hours per year; if fewer, fill out the fields below:
Normal Hours of Source Operation: hours/day
days/week weeks/year
Seasonal use percentage: Dec -Feb: Mar -May: June -Aug: Sept -Nov:
Form APCD-200 - General APEN - Revision 7/2015 2 I A®
COLORADO
o.e,w.ntainm6c
M*&O 6 Z ,be.wNat
Permit Number: AIRS ID Number:
Flour
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 4 - Processing/Manufacturing Information £t Material Use
0 Check box if this information is not applicable to source or process
From what year is the actual annual amount?
Design Process
Rate
(Specify Units)
Actual Annual
Amount
(Specify Units)
Requested Annual
Permit Limit
(Specify -Units)
Material
Consumption:
24,699 lbs/hr
24,699 vlbs/hr
Finished
Product(s):
Bread Loaves
41,032 lbs/hr
41,032 lbs/hr
4
Requested values will become permit limitations. Requested limit(s) should consider future process growth.
Section 5 - Stack Information
Geographical Coordinates
(Latitude/Longitude or UTM)
40.1666555, -105.038308
❑ Check box if the following information is not applicable to the source because emissions will not be emitted from a
stack. If this is the case, the rest of this section may remain blank.
r:
® er•r
1 a
Discharge eight,-
E�e
;>Above Ground Leve}
� �
(Feet)
j'F�
4
ow,Rake
(�1rrF .
r
Velocity
(f&sec)
51.92
450
4034
1.9
Indicate the direction of the stack outlet: (check one)
ID Upward
❑ Horizontal
❑ Downward
0 Other (describe):
Indicate the stack opening and size: (check one)
❑ Upward with obstructing raincap
❑✓ Circular Interior stack diameter (inches): 28
❑ Square/rectangle Interior stack width (inches): Interior stack depth (inches):
O Other (describe):
Form APCD-200 - General APEN - Revision 7/2015 3 I
m®
COLORADO
Departmental lWet
Nam. b Ewuawse
Permit Number:
AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 6 - Combustion Equipment £t Fuel Consumption Information
❑ Check box if this information is not applicable to the source (e.g. there is no fuel -burning equipment associated
with this emission source)
Design Input Rate ;
(MMBTU/hr)
Actual Annual Fuel, Use
(Specify, Units) '
Requested Annual Permit Limit4
(Specify Units)
24.4
24.4 MMBTU/hr
From what year is the actual annual fuel use data?
Indicate the type of fuel used5:
❑■ Pipeline Natural Gas (assumed fuel heating value of 1,020 BTU/SCF)
❑ Field Natural Gas Heating value: BTU/SCF
❑ Ultra Low Sulfur Diesel (assumed fuel heating value of 138,000 BTU/gallon)
❑ Propane (assumed fuel heating value of 2,300 BTU/SCF)
❑ Coal Heating value: BTU/lb Ash Content: Sulfur Content:
❑ Other (describe): Heating value (give units):
4 Requested values will become permit limitations. Requested limit(s) should consider future process growth.
5 If fuel heating value is different than the listed assumed value, please provide this information in the "Other" field.
Section 7 - Criteria Pollutant Emissions Information
Attach all emission calculations and emission factor documentation to this APEN form.
Is any emission control equipment or practice used to reduce emissions? ® Yes ❑ No
If yes, please describe the control equipment AND state the overall control efficiency (% reduction):
Pollutant '
Control Equipment Description
Overall Control Efficiency
(% reduction in emissions)
TSP (PM)
Thermal Oxidizer for two Identical Ovens
98
PMio
PM2.s
SOX
Thermal Oxidizer for two Identical Ovens
98
NOx
Thermal Oxidizer for two Identical Ovens
98
CO
Thermal Oxidizer for two Identical Ovens
98
VOC
Thermal Oxidizer for two Identical Ovens
98
Other:
Form APCD-200 - General APEN - Revision 7/2015
4I
A®
Department
COLORADO
d
Permit Number:
AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 7 (continued)
From what year is the following reported actual annual emissions data?
Use the following table to report the criteria pollutant emissions from source:
(Use the data reported in Sections 4 and 6 to calculate these emissions.)
Pollutant
Uncontrolled
Emission
(Specify Units) ; Factort
Emission
Factor.
Source
(AP 41, Mfg
etc)
Actual Annual Emissions
_ -.. • .
Requested Annual Permit
4
z 4 ;
Emission Limits) __
a�_, r- , .
Uncontrolled
(Tons/year) *
Controlled
(Tons/year)
Uncontrolled
(Tons/year)
Controlled
(Tons/year)
TSP (PM)
7.6
AP -42
.8
.8
PMT()
PM25
SO„
.6
AP -42
.06
.06
NOX
100
AP -42
10.48
10.48
CO
84
AP -42
8.8
8.8
VOC
5.5
AP -42
282.65
6.77
282.65
6.77
Other:
4Requested values will become permit limitations. Requested limit(s) should consider future process growth.
6Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
Section 8 - Non -Criteria Pollutant Emissions Information
Does the emissions source have any uncontrolled actual emissions of non -criteria
pollutants (e.g. HAP- hazardous air pollutant) equal to or greater than 250 lbs/year? Yes No
If yes, use the following table to report the non -criteria pollutant (HAP) emissions from source:
CAS
Number
Chemical Name
Overall
Control
Efficiency
Uncontrolled
Emission
Factor :
(specify units) --
Emission Factor
Source .
(AP -42 Mfg. etc)
Uncontrolled
Actual
Emissions
(lbs/year)
Controlled
Actual
Emissions6
(Ibslyear)
6Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating, leave blank.
Form APCD-2OO - General APEN - Revision 7/2015
D 'CO
LOR
,RAO
5 CO1O AD
IWMb GNvnn.Y
Permit Number: AIRS ID Number:
[Leave blank unless APCD has already assigned a permit # and AIRS ID]
Section 9 - Applicant Certification
I hereby certify that all information contained herein and information submitted with this application is complete, true
and correct.
Signature of Legally Authorized Person (not a vendor or consultant) Date
/ eO
S<L
Name (please print) Title
Check the appropriate box to request a copy of the:
❑� Engineer's Preliminary Analysis conducted
0 Draft permit prior to issuance
❑� Draft permit prior to public notice
(Checking any of these boxes may result in an increased fee and/or processing time)
This emission notice is valid for five (5) years. Submission of a revised APEN is required 30 days prior to expiration
of the five-year term, or when a reportable change is made (significant emissions increase, increase production,
new equipment, change in fuel type, etc). See Regulation 'No. 3, Part A, II.C. for revised APEN requirements.
Send this form along with $152.90 to:
Colorado Department of Public Health and
Environment
Air Pollution Control Division
APCD-SS-B 1
4300 Cherry Creek Drive South
Denver, CO 80246-1530
Telephone: (303) 692-3150
For more information or assistance call:
Small Business Assistance Program
(303) 692-3175 or (303) 692-3148
Or visit the APCD website at:
www.colorado.gov/pacific/cdphe/air-permits
Form APCD-200 - General APEN - Revision 7/2015 6
A®
COLORADO
Hello