The URL can be used to link to this page

Browse Search

Home My WebLink About20202722.tiff C,. 4 . COLORADO tteDepartment of Public RECEIVED Health b Environment AUG 3 1 2020 WELD COUNTY COMMISSIONERS Weld County - Clerk to the Board 1150 0 St PO Box 758 Greeley, CO 80632 August 26, 2020 Dear Sir or Madam: On August 27, 2020, the Air Pollution Control Division will begin a 30-day public notice period for Sun Mountain Inc. A copy of this public notice and the public comment packet are enclosed. Thank you for assisting the Division by posting a copy of this public comment packet in your office. Public copies of these documents are required by Colorado Air Quality Control Commission regulations. The packet must be available for public inspection for a period of thirty (30) days from the beginning of the public notice period. Please send any comment regarding this public notice to the address below. Colorado Dept. of Public Health Et Environment APCD-SS-B1 4300 Cherry Creek Drive South Denver, Colorado 80246-1530 Attention: Public Notice Coordinator 4300 Cherry Creek Drive S., Denver, CO 80246-1530 P 303-692-2000 www.colorado.gov/cdphe I 0; Jared Potis, Governor I Jill Hunsaker Ryan,MPH, Executive Director i. . PV b r, c Re v;e GJ CC:p (TP), HL(D5) Pw(SM/ER/cH/crs) 2020-2722 04/lN/20 ©6(aM) 09/03/20 .,00:.M Air Pollution Control Division `�C'DPH Notice of a Proposed Project or Activity Warranting Public CDPHE Comment Website Title: Sun Mountain Inc. - None - Weld County Notice Period Begins: August 27, 2020 Notice is hereby given that an application for a proposed project or activity has been submitted to the Colorado Air Pollution Control Division for the following source of air pollution: Applicant: Sun Mountain Inc. Facility: None Wood Products Coating Facility 140 Commerce Road, Berthoud Weld County The proposed project or activity is as follows: The Applicant proposes to reduce VOC emission from the facility to below the major source threshold and obtain a synthetic minor permit. The Division has determined that this permitting action is subject to public comment per Colorado Regulation No. 3, Part B, Section III.C due to the following reason(s): • permitted emissions exceed public notice threshold values in Regulation No. 3, Part B, Section III.C.1.a (25 tpy in a non-attainment area and/or 50 tpy in an attainment area) • the source is requesting a federally enforceable limit on the potential to emit in order to avoid other requirements The Division has made a preliminary determination of approval of the application. A copy of the application, the Division's analysis, and a draft of Construction Permit 98WE0023 have been filed with the Weld County Clerk's office. A copy of the draft permit and the Division's analysis are available on the Division's website at https://www.colorado.gov/pacific/cdphe/air-permit-public-notices The Division hereby solicits submission of public comment from any interested person concerning the ability of the proposed project or activity to comply with the applicable standards and regulations of the Commission. The Division will receive and consider written public comments for thirty calendar days after the date of this Notice. Comments may be submitted using the following options: • Use the web form at https://www.colorado.gov/pacific/cdphe/air-permit-public-notices. This page also includes guidance for public participation • Send an email to cdphe.commentsapcd®state.co.us • Send comments to our mailing address: Sunday A. Fadeyi, P.E. Colorado Department of Public Health and Environment 4300 Cherry Creek Drive South, APCD-SS-B1 Denver, Colorado 80246-1530 ja.zo COLORADO 1 Department of Public Health ft Environment `C , y. COLORADO Air Pollution Control Division Department of Public Health&Environment CONSTRUCTION PERMIT Permit number: 98WE0023 Issuance: 7 Date issued: Issued to: Sun Mountain Inc Facility Name: None Plant AIRS ID: 123-0533 Physical Location: 140 Commerce Road, Berthoud County: Weld General Description: Wood Products Coating Facility Equipment or activity subject to this permit: Facility AIRS Description Equipment ID Point N/A 001 Surface coating operations involving the use of volatile materials, including paints, diluents, and cleaning solvents with over-spray filters to control particulate emissions. Changes to the paint booths or addition of new booths will not warrant any modification to this permit unless the change results in air pollutant emissions increase as stipulated below in this permit. THIS PERMIT IS GRANTED SUBJECT TO ALL RULES AND REGULATIONS OF THE COLORADO AIR QUALITY CONTROL COMMISSION AND THE COLORADO AIR POLLUTION PREVENTION AND CONTROL ACT C.R.S. (25-7- 101 et seq),TO THOSE GENERAL TERMS AND CONDITIONS INCLUDED IN THIS DOCUMENT AND THE FOLLOWING SPECIFIC TERMS AND CONDITIONS: REQUIREMENTS TO SELF-CERTIFY FOR FINAL APPROVAL 1. This construction permit represents final permit approval to operate this emissions source. Therefore, it is not necessary to self-certify. (Regulation Number 3, Part B, III.G.5). EMISSION LIMITATIONS AND RECORDS 2. Emissions of air pollutants must not exceed the following limitations (as calculated using the emission factors included in the Notes to Permit Holder section of this permit). Monthly records of the actual emission rates must be maintained by the applicant and made available to the Division for inspection upon request. (Reference: Regulation Number 3, Part B, II.A.4.) Annual Limits: Facility AIRS Tons per Year Emission Equipment ID Point PM PM10 PM2.5 5O2 NOX VOC CO Type N/A 001 2.0 2.0 2.0 -- -- 40.0 -- Point See "Notes to Permit Holder"for information on emission factors and methods used to calculate limits. Page 1 of 6 »y,-... COLORADO Air Pollution Control Division Department of Public Heath&Environment Compliance with the annual limits, for criteria air pollutants, must be determined on a rolling twelve (12)month total. By the end of each month,a new twelve-month total is calculated based on the previous twelve months' data. The permit holder must calculate actual emissions each month and keep a compliance record on site or at a local field office with site responsibility for Division review. The owner or operator must use the emission factors found in "Notes to Permit Holder" to calculate emissions and show compliance with the limits. The owner or operator must submit an Air Pollutant Emission Notice (APEN) and receive a modified permit prior to the use of any other method of calculating emissions. 3. The emission points in the table below must be maintained, and operated with the control equipment as listed. The emission control devices must be inspected, monitored, maintained / renewed, and operated as per the manufacturers' recommendations, or maintained in accordance with good air pollution control practices to ensure the satisfactory performance of the devices. (Reference: Regulation Number 3, Part B, III.E.) Facility Equipment ID AIRS Control Device Controlled Pollutants Point Paint booths 001 Exhaust filters/paint arresters PM (Volatile materials Usage) PROCESS LIMITATIONS AND RECORDS 4. This source must be limited to the following maximum consumption, processing and/or operational rates as listed below. Monthly records of the actual process rate must be maintained by the applicant and made available to the Division for inspection upon request. (Reference: Regulation Number 3, Part B, II.A.4) Process/Consumption Limits Facility AIRS Process Parameter Annual Limit Equipment ID Point N/A 001 Volatile materials usage Will be limited by the VOC limits above.* Note * Emissions of organic material released during clean-up operations, disposal, and other fugitive emissions must be included when determining total emissions, unless the source owner or operator documents that the VOC's are collected and disposed of in a manner that prevents evaporation to the atmosphere. Compliance with the yearly process limits must be determined on a rolling twelve (12) month total. By the end of each month a new twelve-month total is calculated based on the previous twelve months' data. The permit holder must calculate monthly process rates and keep a compliance record on site or at a local field office with site responsibility, for Division review. 5. The owner or permit holder must maintain adequate recordkeeping and must keep a compliance record on site for Division review. (Reference: Regulation Number 3, Part B.III.E) STATE AND FEDERAL REGULATORY REQUIREMENTS 6. Visible emissions must not exceed twenty percent (20%) opacity during normal operation of the source. During periods of startup, process modification, or adjustment of control equipment visible emissions must not exceed 30% opacity for more than six minutes in any sixty consecutive minutes. Opacity must be determined using EPA Method 9. (Reference: Regulation Number 1, II.A.1. a 4.) 7. This source is subject to the odor requirements of Regulation Number 2. (State only enforceable) Page 2 of 6 C ,, ,v,.....,t~•r COLORADO Air Pollution Control Division Department of Public Health b Environment 8. This source is subject to the requirements of Regulation Number 7.V. regarding Disposal of Volatile Organic Compounds as follows: No person must dispose of volatile organic compounds by evaporation, or spillage unless RACT is utilized. (Regulation Number 7.V A) 9. This source is located in an ozone non-attainment or attainment-maintenance area but is not subject to the Reasonably Available Control Technology (RACT) requirements of Regulation Number 3, Part B, III.D.2 as it is an existing source that is not being modified. OPERATING& MAINTENANCE REQUIREMENTS 10. This source is not required to follow a Division-approved operating and maintenance plan. The source shall follow the manufacturer's operating and maintenance recommendations or shall follow good air pollution control practices. COMPLIANCE TESTING AND SAMPLING Initial Testing Requirements 11. Initial testing is not required for this source. Periodic Testing Requirements 12. Periodic testing is not required for this source. ADDITIONAL REQUIREMENTS 13. All previous versions of this permit are cancelled upon issuance of this permit. 14. The permit number must be marked on the subject equipment for ease of identification. (Reference: Regulation Number 3, Part B, III.E.) (State only enforceable) 15. A Revised Air Pollutant Emission Notice (APEN) must be filed: (Reference: Regulation Number 3, Part A, II.C.) a. By April 30 of the year following a significant increase in emissions. A significant increase in emissions is defined as follows:: For any criteria pollutant: For sources emitting less than 100 tons per year, a change in actual emissions of five tons per year or more, above the level reported on the last APEN submitted; or For volatile organic compounds (VOC) and nitrogen oxide (NOx) sources in an ozone non- attainment area emitting less than 100 tons of VOC or nitrogen oxide per year, a change in actual emissions of one ton per year or more or five percent, whichever is greater, above the level reported on the last APEN submitted; or For sources emitting 100 tons per year or more of a criteria pollutant, a change in actual emissions of five percent or 50 tons per year or more, whichever is less, above the level reported on the last APEN submitted; or For sources emitting any amount of lead, a change in actual emissions, above the level reported on the last APEN submitted, of fifty (50) pounds of lead Page 3 of 6 COLORADO VtAir Pollution Control Division igf Department of Public Health b Ermronment For any non-criteria reportable pollutant: If the emissions increase by 50% or five (5) tons per year, whichever is less, above the level reported on the last APEN submitted to the Division. a. Whenever there is a change in the owner or operator of any facility, process, or activity; or b. Whenever new control equipment is installed, or whenever a different type of control equipment replaces an existing type of control equipment; or c. Whenever a permit limitation must be modified; or d. No later than 30 days before the existing APEN expires. GENERAL TERMS AND CONDITIONS: 16. This permit and any attachments must be retained and made available for inspection upon request. The permit may be reissued to a new owner by the Division as provided in Regulation Number 3, Part B, II.B upon a request for transfer of ownership and the submittal of a revised APEN and the required fee. 17. If this permit specifically states that final approval has been granted, then the remainder of this condition is not applicable. Otherwise, the issuance of this construction permit is considered initial approval and does not provide"final" approval for this activity or operation of this source. Final approval of the permit must be secured from the APCD in writing in accordance with the provisions of 25-7-114.5(12)(a) C.R.S. and AQCC Regulation Number 3, Part B, III.G. Final approval cannot be granted until the operation or activity commences and has been verified by the APCD as conforming in all respects with the conditions of the permit. Once self-certification of all points has been reviewed and approved by the Division, it will provide written documentation of such final approval. Details for obtaining final approval to operate are located in the Requirements to Self-Certify for Final Approval section of this permit. The operator must retain the permit final approval letter issued by the Division after completion of self-certification with the most current construction permit. 18. This permit is issued in reliance upon the accuracy and completeness of information supplied by the applicant and is conditioned upon conduct of the activity, or construction, installation and operation of the source, in accordance with this information and with representations made by the applicant or applicant's agents. It is valid only for the equipment and operations or activity specifically identified on the permit. (Reference: Regulation Number 3, Part B III.E.) By: By: Sunday A. Fadeyi, P.E. R K Hancock III, P.E. Permit Engineer Construction Permits Unit Supervisor Permit History Issuance Date Description Issuance 1 October 16, 1998 Permit Exemption / APEN Required letter Issuance 2 March 24, 2000 IA Modification-1: Increase in VOC emissions. Processed as a synthetic minor source permit. Issuance 3 July 13, 2001 IA Modification-2: Deletion of conditions no longer applicable; change in the name of permittee from Sun Mountain Door Company to Sun Mountain, Inc. Issuance 4 February 6, 2003 FA Modification-2: Final Approval Page 4 of 6 C .. .y .....-I. COLORADO Mr Pollution Control Division Department of Publ?c Health b Environment Issuance 5 December 16, 2004 FA Modification-3. Addition of a spray booth. Issuance 6 FA Modification-4: Updated equipment to include dust collectors and Delle Vedove equipment. Issuance 7 This Issuance VOC emission reduced from 90.0 to 40.0 tons per year; Final Approval reissued to Sun Mountain Inc. Notes to Permit Holder (as of date of permit issuance): 1) The production or raw material processing limits and emission limits contained in this permit are based on the production/processing rates requested in the permit application. These limits may be revised upon request of the permittee providing there is no exceedence of any specific emission control regulation or any ambient air quality standard. A revised air pollutant emission notice (APEN) and application form must be submitted with a request for a permit revision. (Reference: Regulation Number 3, Part B II.A.4.) 1) This source is subject to the Common Provisions Regulation Part II, Subpart E, Affirmative Defense Provision for Excess Emissions During Malfunctions. The permittee must notify the Division of any malfunction condition which causes a violation of any emission limit or limits stated in this permit as soon as possible, but no later than noon of the next working day, followed by written notice to the Division addressing all of the criteria set forth in Part II.E.1. of the Common Provisions Regulation. See: https://www.colorado.gov/pacific/cdphe/aqcc-regs. 2) The following emissions of non-criteria reportable air pollutants are estimated based upon the process limits as indicated in this permit. This information is listed to inform the operator of the Division's analysis of the specific compounds emitted if the source(s) operate at the permitted limitations. AIRS P (BIN) CAS# Emission Rate (lb/yr) Point Uncontrolled Controlled 100-41-4 Ethylbenzene 600 600 001 1330-20-7 Xylene 1,831 1,831 108-88-3 Toluene 1,681 1,681 3) The emission levels contained in this permit are based on the following emission factors: Point 001: Volatile Materials Usacie: VOC/HAP Emissions: Mass balance assuming that the entire solvent content in the raw material minus the solvent content of the wastes sent off-site and the solvent contained in product is emitted. VOCemissions= (MaterialSconsumption)*(VOC%), VOCemissions(pounds per year) = (Raw materialconsumption)*(VOC%)) - (Products)*(VOC%) - (Wastes)*(VOC TSP/PMi o/PM2.5 emissions = (Product consumption)*(Particulate%)*(1-TE)*(1-CE), Where: Materialsconsumpeon= Beginning Inventory+ New Purchases—End Inventory VOC%/HAP% is in weight percent(i.e.VOC/HAP's weight percent in the product), Particulate%is in weight percent(i.e. particulate's weight percent in the product) TE=Transfer Efficiency in weight percent CE =Control efficiency if weight fraction If volatile materials consumption is in tons,then emissions are in tons per year. If volatile materials consumption is in Ibs, then emissions are in lbs per year. Page 5 of 6 eCOLORADO Air Pollution Control Division a Department of Public Health b Environment 4) In accordance with C.R.S. 25-7-114.1, each Air Pollutant Emission Notice (APEN) associated with this permit is valid for a term of five years from the date it was received by the Division. A revised APEN must be submitted no later than 30 days before the five-year term expires. Please refer to the most recent annual fee invoice to determine the APEN expiration date for each emissions point associated with this permit. For any questions regarding a specific expiration date call the Division at (303)-692- 3150. 5) This facility is classified as follows: Applicable Requirement Status Title V Operating Permit Minor: PM, Synthetic Minor: VOC PSD Minor: PM NANSR Synthetic Minor: VOC 6) The permit holder is required to pay fees for the processing time for this permit. An invoice for these fees will be issued after the permit is issued. The permit holder must pay the invoice within 30 days of receipt of the invoice. Failure to pay the invoice will result in revocation of this permit (Reference: Regulation Number 3, Part A, VI.B.) 7) Unless specifically stated otherwise, the general and specific conditions contained in this permit have been determined by the Division to be necessary to assure compliance with the provisions of Section 25-7-114.5(7)(a), C.R.S. 8) Each and every condition of this permit is a material part hereof and is not severable. Any challenge to or appeal of a condition hereof Must constitute a rejection of the entire permit and upon such occurrence, this permit Must be deemed denied ab initio. This permit may be revoked at any time prior to self-certification and final authorization by the Division on grounds set forth in the Colorado Air Pollution Prevention and Control Act and regulations of the AQCC including failure to meet any express term or condition of the permit. If the Division denies a permit, conditions imposed upon a permit are contested by the applicant, or the Division revokes a permit, the applicant or owner or operator of a source may request a hearing before the AQCC for review of the Division's action. 9) Section 25-7-114.7(2)(a), C.R.S. requires that all sources required to file an Air Pollutant Emission Notice (APEN) must pay an annual fee to cover the costs of inspections and administration. If a source or activity is to be discontinued, the owner must notify the Division in writing requesting a cancellation of the permit. Upon notification, annual fee billing will terminate. 10) Violation of the terms of a permit or of the provisions of the Colorado Air Pollution Prevention and Control Act or the regulations of the AQCC may result in administrative, civil or criminal enforcement actions under Sections 25-7-115 (enforcement), -121 (injunctions), -122 (civil penalties), -122.1 (criminal penalties), C.R.S. Page 6 of 6 CCOLORADO _` �/ Air Pollution Control Division Department of Public Health b Environment AIR POLLUTION CONTROL DIVISION PRELIMINARY ANALYSIS DATE: August 26, 2020 PERMIT NUMBER: 98WE0023 APPLICANT: Sun Mountain Inc. REVIEW ENGINEER: Sunday Fadeyi, P.E. CONTROL ENGINEER: R K Hancock III, P.E PROJECT DESCRIPTION Sun Mountain Inc. - Wood Products Coating Facility - Weld County The applicant proposes to modify their existing permit for the above facility, in Weld County, CO. This project is the modification to decrease permit emissions' limits: VOC from 90.0 to 40.0 tons per year. The source's emissions profile is as follows: SUMMARY OF FACILITY WIDE EMISSIONS EMISSIONS TSP PM10 PM2.5 5O2 NOx VOC CO H2S HAPs REMARKS (tons/year) Current Project 2.0 2.0 2.0 40.0 2.1 Synthetic Emission minor for Title V and Non Attainment PTE 45.0 45.0 45.0 --- 90.0 -- -- 4.6 Area New Source Review Programs SOURCE'S IMPACTS (ug/mJ For the criteria air pollutant emissions, the source's impact analysis is not required at this time per the Colorado Modeling Guideline for Air Quality Permits, Table 1 since permitted emission levels will be decreasing Therefore, the source, as proposed, will not cause any violation of the National Ambient Air Quality Standard. SOURCE CLASSIFICATION The project has the potential to emit (PTE) of 90.0 tons of VOC per year. The draft permit has limitations that will reduce emissions to 40.0 tons per year of VOC. Since this project has the potential to emit greater than 50 tons per year of VOC, this project is considered to be a synthetic minor source for both the Nonattainment New Source Review (NANSR), and Title V Operating Permit programs. Comment is required for the source being a synthetic minor fromr the NANSR emission. Page 1 of 1 Surface Coating and Solvent Usage APEN AO Form APCD-226 CDPHE Air Pollutant Emission Notice (APEN) and Application for Construction Permit All sections of this APEN and application must be completed for both new and existing facilities, including APEN updates. Incomplete APENs will be rejected and will require re-submittal. Your APEN will be rejected if it is filled out incorrectly, is missing information, or lacks payment for the filing fee. The re-submittal will require payment for a new filing fee. This APEN is to be used for coating, painting, cleaning solvent, and volatile materials usage operations. If your emission source does not fall into one of these categories, there may be a more specific APEN for your source (e.g. mining operations, boiler, print shop, etc.). In addition, the General APEN(Form APCD-200)is available if the specialty APEN options will not satisfy your reporting needs. A list of all available APEN forms can be found on the Air Pollution Control Division(APCD)website. This emission notice is valid for five(5)years. Submission of a revised APEN is required 30 days prior to expiration of the five-year term, or when a reportable change is made(significant emissions increase, increase production, new equipment,change in fuel type, etc.). See Regulation No. 3, Part A, II.C. for revised APEN requirements. Permit Number: 98W E0023 AIRS ID Number: 123/ 0533 /001 ,!_cave blank a;less APCD has already assigned a permit and AIRS ID] Section 1 - Administrative Information Company Name': Sun Mountain Inc Site Name: Site Site Location: 140 Commerce Rd Location County: Weld Berthoud, CO 80513 NAICS or SIC Code: 2499 Mailing Address: 140 Commerce Rd (Include Zip Code) Berthoud, CO 80513 Contact Person: Michael Jennings Phone Number: 970-532-2105 Portable Source z E-Mail Address z: mjennings@sunmountaindoor.com Home Base: Use the full, legal company name registered with the Colorado Secretary of State.This is the company name that will appear on all documents issued by the APCD.Any changes will require additional paperwork. 2 Permits,exemption letters, and any processing invoices will be issued by the APCD via e-mail to the address provided. 432149 COLORADO Form.APCD-226 Suiface Coating and Solvent Usage APEN Revr<ion 12/2019 1 1 4�,='time"' I'I Permit Number: 98W E0023 0023 AIRS ID Number: 1 23/0533/001 • [Leave blank unless APCD has ahready assigned a permit#and MRS 1Dl Section 2 - Requested Action 0 NEW permit OR newly-reported emission source(check one below) 0 STATIONARY source 0 PORTABLE source -OR- 0 MODIFICATION to existing permit(check each box below that»plies) ❑ Change fuel or equipment ❑ Change company name3 ❑ Add point to existing permit El Change permit limit ❑ Transfer of ownership4 0 Other(describe below) -OR- APEN submittal for update only(Note blank APENs will not be accepted) -ADDITIONAL PERMIT ACTIONS- it ❑ Limit Hazardous Air Pollutants(HAPs)with a federally-enforceable limit on Potential To Emit(PTE) ❑ APEN submittal for permit exempt/grandfathered source Additional Info& Notes: 3 For company name change,a completed Company Name Change Certification Form (Form APCD-106)must be submitted. 4 For transfer of ownership,a completed Transfer of Ownership Certification Form (Form APCD-104)must be submitted. Section 3 - General Information Facility Function: 0 Automobile Coating 0 Metal Parts Coating 0 Plastic Parts Coating 0 Other(explain): Wood Products Coating General description of equipment and purpose: HVLP,Air Assist for coating of wood doors and millwork For existing sources, operation began on: 1998 For new or reconstructed sources, the projected start-up date is: ❑ Check this box if operating hours are 8,760 hours per year; if fewer, fill out the fields below: Normal Hours of Source Operation: 8 hours/day 5 days/week 48 weeks/year SO COLORADO Fo!r3 AP(D-2:_6CoatingtN +,dn.mer+k a Surface and Solvent Usage APEN Rev, ors 12/2019 2 Permit Number: 98W E0023 AIRS ID Number: 123/0533/001 [Leave blank unless APCD has already assigned a permit IT and AIRS ID Section 4 - Equipment Information List the type of equipment located at this facility(e.g. paint booths, dip-tanks, powder coating units, etc.). Attach additional sheets as needed for additional equipment. Process Equipment Descriiption Year of . Control Equipment • unit No. Presen t? (Include Make,Model,and Serial No.) installatlor€ (Yes at M• ) 1 Trim Paint Booth 1998 No 2 Stain Paint Booth 1998 No 3 Top Coat Paint Booth 1998 No 4 5 Is any emission control equipment or practice used to reduce emissions? D Yes No If yes, describe the control equipment AND state the collection and control efficiencies: Collection Efficiency Control Emissions Control Equipment Description - Year of (%of total Efficiency Pollutant emissions (%reduction of (Include Make,Model,and Serial No.) Installation €aptu ecf by captured control- emissions.) equipment) TSP (PM) PM,() PM2.5 SOX NO,, CO VOC Other: asik COLOR A DO Form APCD-226 Surface Coating and Solvent Usage APEN Rev-Jon 12/2019 3 I Permit Number: 98W E0023 AIRS ID Number: 123/0533/001 [Leave blank unless APCD has already assignee a permit#and AIRS IDI Section 5 - Paints, Cleaning Solvents, and Volatile Materials Usage Information Coating Materials Application Method: Note: "TE" means"Transfer Efficiency percent(%)." It is ised to estimate particulate emissions. o Dip, Brush, or Roller(DBR): TE=95% ❑ Electrostatic, High Voltage(EHY):TE=90% ✓❑ High Volume Low Pressure Gun (HVLP):TE= 65% 0 Electrostatic, Low Voltage (ELY): TE=65% • Air-Assisted Airless/Airless (AAA/A): TE=40% 0 Conventional Air Atomizing(CAA): TE= 25% ❑ Others (describe): Actual Average Time Spent for Materials Application: 6 hours/day Actual hours of materials application will be used in conjunction with actual or requested V0C and HAPs emissions to establish the facility's Potential to Emit(PTE). Volatile Materials Usage: List the most commonly used products at your facility below.This includes paint and solvents. You should report any material usage associated with surface preparation and clean-up, in addition to your paint and solvent/thinner use. Attach additional sheets for additional products as needed. Product No. Name of.Pr€sduct Annum Usage SDS Id r Name-_ 1 Stain (HVLP) 4023 gal 2 Primer/Paint (Air Assist) 565 gal 3 WaterbaseGlaze 111 gal 4 Conversion Varnish Interior(Air-Assist) 12329 gal 5 Conversion Varnish Exterior(Air- Assist) 455 gal 6 7 8 9 10 _ COLORA6O 4 Form APCD-226 Surface Coating and Solvent Usage APEN Revision. 12/2019 I A� � Permit Number: 98W E0023 AIRS ID Number: 123/0533/001 [Leave blank unless APCO has already assigned a permit#and AIRS ID} Section 6 - Powder Coatings Usage 0 Check this box if your process does NOT include powder coa ing and skip to Section 7. Actual Usage: tons per year Requested Usages: tons per year Application Method: Transfer Efficiency(TE): Control Device: Control Efficiency(CE): % 5 Requested values will become permit limitations or will be evaluated for exempt status,as applicable,and should consider future process growth. Requested values are required on all APENs,including APEN updates. Section 7 - Geographical/Stack Information • Geographical Coordinates (Latitude/Longitude or t/TM) • 0 Check box if the following information is not applicable to the source because emissions will not be emitted from.a stack. If this is the case, the rest of this section may remain blank. t ass s . a _...A ..e..a Indicate the direction of the stack outlet: (check one) ❑ Upward 0 Downward ❑ Upward with obstructing raincap ❑ Horizontal 0 Other(describe): Indicate the stack opening and size: (check one) 0 Circular Interior stack diameter(inches): ❑ Square/rectangle Interior stack width (inches): Interior stack depth (inches): ❑ Other(describe): ,COLORADO Form APCD-226 Surface Coating and Solvent Usage APEN Revision 12/2019 5 °, =.7= Permit Number: 98W E0023 AIRS ID Number: 123/0533/001 [Leaver blank unless APCD has already assigned a permit#and AIRS ID} Section 8 - Criteria Pollutant Emissions Information Attach all emission calculations and emission factor documental m to this APEN form. From what year is the following reported actual annual emissions data? 201 9 Use the following table to report the criteria pollutant emissions from source: (Use the data reported in Sections 3-6 to calculate these emissions.) Ernlssi Uncuritrolteei �, �.ilektigoimk E a e Pollutant �A .1-(S!):41 :4c or42 . (AP- ,Mfg. Unc trolled Controfte :� . st tilled. efe (t !sty r ftwrslyear) (o sfyeat.z voc 22.2 40 • TSP (PM) PM10 .4 2.0 PM2.5 Other: 5 Requested values will become permit limitations or will be evaluated for exempt status,as applicable,and should consider future process growth. Requested values are required on all APENs,including APEN updates. 6 Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating,provide projected emissions. Section 9 - Non-Criteria Pollutant Emissions Information Does the emissions source have any uncontrolled actual emissions of non-criteria Yes ❑ No pollutants(e.g. HAP-hazardous air pollutant)equal to or greater than 250 lbs/year? If yes, use the following table to report the non-criteria pollutant(HAP)emissions from source: (Use the data reported in Sections 3-6 to calculate these emissions.) Overall controlled Actual CAS Number Chemical Name o: fie, Emiss a ,:,: Etnfs ons6 l fft4en cy (lbsl ear). 108883 Toluene 933 1330207 Xylene Isomers 1016 100414 Ethylbenzene 333 6 Annual emission fees will be based on actual controlled emissions reported. If source has not yet started operating,provide projected emissions. Co LnOR DDO Form APCD-226 Surface Coating and Solvent Usage APEN Revision 12/2019 6 I AmyHMFb E.t.a,+ant Permit Number: 98WE0023 AIRS ID Number: 123/0533/001 [Leave blank unless APCD has already ass[aned a Per{wilt n and AIRS ID] Section 10 - Applicant Certification I hereby certify that nformation con ed herein and inforr Rion submitted with this application is complete, true, and corre Digitally signed by Mike Jennings Mike ennings Date:2020.06.05 8117:33-06O0' 6/5/2020 Signature of Legally Authorized Person (not a vendor or consultant) Date Mike Jennings COO Name(print) Title Check the appropriate box to request a copy of the: Draft permit prior to issuance ❑Draft permit prior to public notice (Checking any of these boxes may result in an increased fee and/or processing time) This emission notice is valid for five (5)years. Submission of a revised APEN is required 30 days prior to expiration of the five-year term, or when a reportable change is made (significant emissions increase, increase production, new equipment,change in fuel type, etc.). See Regulation No. 3, Part A, II.C. for revised APEN requirements. Send this form along with$191.13 to: For more information or assistance call: Colorado Department of Public Health and Environment Small Business Assistance Program Air Pollution Control Division (303)692-3175 APCD-SS-B1 OR 4300 Cherry Creek Drive South (303)692-3148 Denver, CO 80246-1530 APCD Main Phone Number Make check payable to: (303)692-3150 Colorado Department of Public Health and Environment COLORADO Form APCD-226 Surface Coating and Solvent Usage APEN Revision 12.2019 7 I NV ow Hello